A leaking toilet is one of those problems that starts small and gets expensive fast. That faint trickle you hear between flushes? It could be sending thousands of litres of water straight down the drain every year, and your water bill along with it.
For aussie homeowners, this hits a bit harder. Our cities relies heavily on desalination and groundwater to keep taps flowing, and every wasted litre puts more pressure on a system that’s already working hard. The Water Corporation estimates that even a small toilet trickle can waste around 9,000 litres a year. A constantly running toilet? That number jumps to 60,000 litres or more.
The good news is that many leaking toilet issues are straightforward to diagnose, and some are simple enough to fix yourself with a trip to the hardware store. This guide covers the most common causes of a leaking toilet, how to work out where the problem is coming from, and when it makes sense to call in a licensed plumber.
What Causes a Toilet to Leak?
Toilets look simple from the outside, but there’s a fair bit going on inside the cistern. Most leaks come down to a handful of parts wearing out over time. Here’s a quick overview before we dig into each one.
| Cause | What’s Happening | Common Signs | DIY or Plumber? |
| Worn seating washer | Rubber seal on flushing valve degrades | Trickle at back of bowl, cistern refills on its own | DIY friendly |
| Faulty inlet valve | Valve doesn’t shut off, water overfills cistern | Constant running sound, high water level in cistern | DIY possible |
| Cracked cistern or bowl | Hairline crack lets water escape | Pooling water on floor, visible crack | Plumber needed |
| Loose connections | Bolts/gaskets between cistern and bowl loosen | Drips during or after flush, water at back of toilet | DIY possible |
| Worn wax ring/pan collar | Seal between toilet base and floor drain fails | Water around base after flushing | Plumber required |
Worn Seating Washer (Flushing Valve Seal)
This is the most common cause of a leaking toilet. The seating washer sits at the base of the flushing valve inside the cistern. Its job is to create a watertight seal that stops water from constantly flowing into the bowl. Over time, the rubber degrades, hardens, or warps, and water starts to seep through.
You’ll usually notice this as a slow, steady trickle at the back of the bowl, or you might hear the cistern refilling itself periodically even though nobody has flushed. It’s a common issue on both older and newer toilets.
Faulty Inlet Valve
The inlet valve controls how much water flows into the cistern after each flush. When the washer inside the valve wears out or the float mechanism gets stuck, water keeps entering the cistern past its fill line. That excess water has to go somewhere, so it overflows into the bowl through the overflow tube.
A telltale sign of this problem is the sound of running water that doesn’t stop after the cistern should have finished filling. If your toilet keeps running after a flush, the inlet valve is one of the first things to check. Sometimes you can see the water level sitting noticeably higher than the overflow mark.
Cracked Cistern or Bowl

Porcelain is tough, but it’s not indestructible. Hairline cracks in the cistern or the bowl itself can develop over years of use, temperature changes, or accidental impact. These cracks often start small and slowly worsen.
If you’re finding water pooling on the floor around the toilet and the connections all look tight, a cracked cistern or bowl could be the culprit. Unfortunately, this one usually means replacing the affected part entirely.
Loose Connections Between the Cistern and Bowl
On two-piece toilets (where the cistern and bowl are separate), a set of bolts, nuts, and gaskets hold everything together. These fittings can loosen over time, especially in older setups. When they do, water can leak out from between the two sections, usually most noticeable during or just after a flush.
The supply line connecting the wall tap to the cistern is another spot to check. A loose connection or a worn hose can produce a slow drip that runs down the back of the toilet or onto the floor.
Worn Wax Ring or Pan Collar
The wax ring (or rubber pan collar on newer installations) sits between the base of the toilet and the floor drain. It creates the seal that prevents water and sewage from leaking out at the base. Over years, the wax compresses, dries out, or simply breaks down.
Water appearing around the base of the toilet, especially after flushing, is a strong indicator. This repair involves removing the entire toilet and resetting it with a new seal, so it’s one that typically needs a licensed plumber.
How Do You Know If Your Toilet Is Leaking?
Not all toilet leaks are obvious. Some are completely silent, and the only clue might be an unexpectedly high water bill. Here are a few ways to find out if your toilet has a hidden leak.
The Food Colouring Test
This is the simplest check you can do. Drop four or five drops of food colouring into the cistern and leave it for 30 minutes without flushing. If colour shows up in the bowl, water is leaking past the flushing valve seal and you’ve confirmed a leak. The Water Corporation recommends this as a quick diagnostic for Perth homeowners.
Just remember to flush a couple of times afterwards so the dye doesn’t stain the bowl.
Visual and Sound Clues
Staining where water runs down the back of the bowl is a common giveaway. That stain builds up because water is trickling through slowly and sitting there longer than it should. Pooling water around the base is another red flag.
Listen for sounds too. A hissing or trickling noise between flushes usually means water is moving when it shouldn’t be. If your cistern seems to randomly refill itself every now and then, that’s the inlet valve topping up water that’s been slowly leaking into the bowl.
The Water Meter Test
If you want to check for leaks across the whole house, turn off every tap and water-using appliance. Read your water meter, wait 30 minutes, then read it again. If the number has changed, you’ve got a leak somewhere on the property. This won’t pinpoint the toilet specifically, but it’s a solid first step if you suspect something is off.
How Much Water Does a Leaking Toilet Waste?
More than most people expect. The numbers are worth paying attention to, especially in Perth where water is a resource we can’t afford to take for granted.
A small, slow leak from a deteriorating cistern seal can waste upwards of 9,000 litres per year. That alone is enough to fill a decent-sized backyard pool. But it gets worse. According to Greater Western Water, a continuously running toilet can blow through 60,000 to 96,000 litres annually. That’s the equivalent of leaving a garden hose running for days on end.
To put it in dollar terms, the average leaking cistern loses between a quarter of a litre and a full litre per minute. Over a 92-day billing cycle, that adds up to somewhere between 30,000 and 70,000 litres of water you’re paying for but never actually using. For a household on scheme water in Perth, that’s a noticeable hit to the quarterly bill.
This isn’t just a Perth problem either. Water authorities across every Australian state and territory have flagged leaking toilets as a major source of household water waste. Here’s how the numbers stack up around the country.
| State/Territory | Water Authority | Leaking Toilet Waste | Key Stat |
| WA | Water Corporation | Up to 9,000 L/year (trickle) | $400 Waterwise Toilet Rebate available |
| NSW | Sydney Water | Up to 260 L/day (visible leak) | Up to 96,000 L/year if running |
| VIC | South East Water | Up to 60,000-96,000 L/year | A trickle can add $425+/year to bills |
| QLD | QLD Government | Up to 18 buckets/day (visible) | Up to 22 L/min for a leaky loo |
| SA | SA Water | Up to 260 L/day | 50% allowance on water lost |
| TAS | TasWater | Up to 60,000 L/year | Rebate up to 50% excess usage |
| NT | Power and Water | Over 200,000 L/year | NT uses 2x national avg water |
| ACT | ACT Government | 4,000+ L/year (slow leak) | Food colouring test recommended |
Perth’s water supply depends on desalination plants and groundwater, and in a city where water restrictions are a regular part of life, fixing a leaking toilet isn’t just about saving money. It’s about doing your part for the community and the environment. Homeowners across suburbs like Morley, Bayswater, and Dianella deal with this more often than you’d think.
Can You Fix a Leaking Toilet Yourself?
For some of the most common causes, yes. Replacing a seating washer or adjusting a float valve are jobs most handy homeowners can tackle with basic tools and a bit of patience. Here’s the general process for the most common fix.
Replacing a Seating Washer (Flushing Valve Seal)

Start by locating the cistern tap, which is usually at the base of the cistern where the hose or pipe connects to the wall. Turn it off by rotating clockwise. Remove the cistern lid and flush the toilet to empty the tank.
Next, remove the flushing valve. On most modern toilets, this involves either twisting the top section or pressing release clips on the sides. Take note of the position before you pull it out so you can reinstall it the same way.
Flip the flushing valve upside down and you’ll see the seating washer, a rubber disc attached to the bottom. Peel it off, take it to the hardware store as a reference, and buy a matching replacement. Clip the new washer onto the base, make sure it’s centred, and click the valve back into place.
Turn the cistern tap back on and watch for leaks. If the water stops trickling into the bowl, you’ve sorted it.
What About the Inlet Valve?
If the problem is with the inlet valve, you may be able to replace the internal seal yourself. Hold the top of the valve, pull the lever arm up until the float reaches the top, then twist the valve body anti-clockwise to expose the seal. Swap it for a new one and reassemble.
That said, inlet valves vary quite a bit between brands and models. If you’re not confident about the specific mechanism in your cistern, or if the valve itself is old and corroded, it’s often simpler and more reliable to have a plumber replace the whole unit.
When Should You DIY and When Should You Call a Plumber?
Not every leaking toilet needs a professional. But some repairs absolutely do. Here’s a quick breakdown to help you decide.
| Repair | Difficulty | Approx. Cost (DIY) | Plumber Needed? |
| Replace seating washer | Easy | $5 – $15 | No |
| Replace inlet valve seal | Moderate | $10 – $25 | Optional |
| Tighten cistern bolts/connections | Easy | $0 (tools only) | No |
| Replace full inlet valve | Moderate | $20 – $50 | Recommended |
| Replace wax ring / pan collar | Hard | N/A | Yes (licensed) |
| Replace cracked cistern or bowl | Hard | N/A | Yes (licensed) |
| Full toilet suite replacement | Hard | N/A | Yes (licensed) |
In Western Australia, any plumbing work that connects to the sewage system must be carried out by a licensed plumber. That covers wax ring replacements, pan collar work, and full toilet replacements. If you’re not sure whether your repair crosses that line, it’s always better to check.
And here’s something a lot of people don’t realise: in WA, this isn’t just a recommendation. It’s a legal requirement. Whether you’re in Bassendean, Beechboro, or anywhere else in the Perth metro area, the same rules apply.
If you’ve tried a DIY fix and the leak persists, there could be a deeper issue with the valve seat or the flush mechanism housing. Sometimes the seat has corroded or become uneven, and no amount of new washers will create a proper seal. At that point, a plumber can assess whether the seat needs regrinding or the whole assembly needs replacing.
If you’re in Perth and need a hand, toilet installation is one of the things we handle most often at VTPG. Sometimes a quick call saves you a weekend of troubleshooting.
Should You Upgrade to a Dual Flush Toilet?
If your leaking toilet is an older single-flush model, it might be worth thinking about a full replacement rather than a repair. The water savings can be significant.
| Old Single Flush | WELS 4-Star Dual Flush | |
| Full flush | Up to 12 litres | 4.5 litres |
| Half flush | N/A (single flush only) | 3 litres |
| Daily use (family of 4) | ~240 litres | ~72 litres |
| Annual water use | ~87,600 litres | ~26,280 litres |
| Potential annual savings | – | Up to 50,000+ litres |
| WA rebate available? | Eligible for replacement | $400 per toilet (up to 2) |
The Water Corporation is currently offering a Waterwise Toilet Rebate of $400 to help cover the cost of replacing a single-flush toilet with a WELS 4-star rated model. You can claim up to two toilets per property, which means up to $800 back in your pocket. The rebate has been extended through to 31 December 2025, but allocations are limited, so it’s worth acting sooner rather than later.
To be eligible, your property needs to be connected to Water Corporation scheme water, and the new toilet must be installed by a licensed plumber. You’ll need to keep your receipt and take before-and-after photos of the old and new toilets for your claim.
It’s worth noting that from the early 1980s, all new homes built in WA were required to have dual flush toilets installed. So if your home still has a single flush system, it’s likely been there for over 40 years, and it’s probably due for an update regardless of whether it’s leaking.
Frequently Asked Questions
How do I check if my toilet has a hidden leak?
The easiest method is the food colouring test. Add a few drops of food colouring to your cistern and wait 30 minutes without flushing. If the colour appears in the bowl, you have a leak. You can also check your water meter by turning off all taps and appliances, reading the meter, waiting 30 minutes, and reading it again. Any movement on the dial points to a leak somewhere on the property.
How much does it cost to fix a leaking toilet in Perth?
It depends on the cause. Replacing a seating washer is a minor repair and typically costs less than $20 in parts if you do it yourself. A plumber callout for a washer or inlet valve replacement will generally run between $150 and $300 depending on the complexity and parts needed. More involved work like replacing a wax ring, swapping out a cistern, or installing a new toilet suite will cost more, but it’s worth comparing that against the water you’re wasting. A toilet leaking 30,000 to 70,000 litres per billing cycle adds up quickly.
Can a leaking toilet increase my water bill?
Absolutely. A constantly running toilet is one of the most common causes of unexpectedly high water bills. Even a small, silent leak can waste thousands of litres between bills. It’s one of those issues that often goes unnoticed until the bill arrives, which is why regular checks are a good habit to build. If your toilet keeps running after a flush, there’s likely a faulty inlet valve or worn seating washer that needs attention.
Don’t Let a Small Leak Become a Big Problem
A leaking toilet might not seem urgent, but the water waste, the rising bills, and the potential for floor damage all add up faster than you’d think. The good news is that catching it early makes all the difference. A quick food colouring test takes two minutes and could save you thousands of litres.
For simple washer replacements, it’s a manageable DIY job. For anything more involved, or if you’re just not sure what’s going on inside the cistern, there’s no shame in getting a professional opinion. That’s what we’re here for.
If you’re dealing with a leaking toilet in Perth and want it fixed properly, get in touch with VT Plumbing Group. We’ll find the problem, explain your options, and get things sorted without the runaround.



